Wall Mount for Road and Gravel Bikes Installation guide

Install the two wall holders and protective frame pads, then check the fit for your road or gravel bike.

Time
30 min
Install
Wall mounted
Difficulty
Moderate

[ TOOLS REQUIRED ]

  • Drill
  • Suitable drill bit
  • Spirit level
  • Pencil
  • Screwdriver

View product

Wall Mount for road and gravel bikes with oak rods – StudioVelo3D

Before you start.

All holders, rods, protective pads and screw caps are supplied loose and must be assembled.

Read through the full installation guide before you begin.

  • Check that all parts are present before installation.
  • Make sure your bike frame can rest securely on both soft contact points.
  • Choose a suitable solid wall and the correct fixings for the wall construction.
  • Do not install the mount on a hollow wall using the supplied wall plugs.
  • Check for electrical cables, water pipes or other services before drilling.
  • Make sure there is enough clearance around the bike, including the handlebars, pedals and wheels.
  • Position the bike against the wall first to determine a comfortable mounting height.

[ WHAT IS IN THE BOX ]

  • 2 × wall holders
  • 2 × 30 cm lacquered oak rods with finished ends
  • 2 × protective frame pads for the Ø25 mm oak rods
  • 2 × screw caps
  • 2 × stainless-steel 5 × 40 mm mounting screws
  • 2 × M5 washers
  • 2 × 8 × 40 mm wall plugs

[ WALL TYPE ]

  • Solid, non-hollow walls

Suitable for solid, non-hollow walls only. Do not install on hollow walls or plasterboard partitions. Select fixings that are suitable for the actual wall material.

[ WARNING ]

Install only on a suitable solid, non-hollow wall. Do not install on hollow walls or plasterboard partitions. Use fixings suitable for the wall material. Both contact points must support the frame securely. Maximum bicycle weight: 15 kg.

Watch the installation.

Assembly order: plugs, wall holders, washers and screws, screw caps, oak rods, then protective frame pads. Marking, drilling and placing the bike are covered in the written guide.

Follow the steps.

  1. [ 01 / 06 ]

    Mark the two mounting positions

    The system has two separate wall holders that form a horizontal pair. Position them level at the same height and check the support positions with your bike before marking.

    Mark one fixing point for each holder. The animation shows approximately 60 cm between the holder centres; check that your frame can rest securely on both pads and that the handlebars, pedals and wheels have enough clearance before drilling.

    [ NOTE ]

    Measuring and drilling are preparation steps; they are not shown in the assembly animation.

    [ WARNING ]

    Check for electrical cables, pipes or other services before drilling.

  2. [ 02 / 06 ]

    Fit the plugs, holders, washers and screws

    Drill the two marked holes using a bit and depth suitable for the supplied 8 × 40 mm plugs and your wall material. Clear drilling dust and insert both plugs fully.

    Position each wall holder against the wall. Place one M5 washer at each fixing point, then insert one stainless-steel 5 × 40 mm screw through each washer and holder into its plug.

    Tighten both fixings until the holders sit firmly and flat against the wall. Check that the pair is level and neither holder moves.

    [ NOTE ]

    Follow the plug instructions for the required drilling diameter and depth.

    [ WARNING ]

    Do not overtighten or deform the holders. Use the supplied plugs only in suitable solid walls.

  3. [ 03 / 06 ]

    Fit both screw caps

    Fit one screw cap over each screw head and seat both caps fully.

    Complete this step before inserting the wooden rods.

  4. [ 04 / 06 ]

    Insert both 30 cm rods

    Align each 30 cm oak rod with its wall holder opening.

    Push the rods straight into the holders along their insertion axes until both are seated securely. Use steady pressure for the final part of the snug fit.

    [ NOTE ]

    Fit the rods before the protective frame pads.

    [ WARNING ]

    Do not bend the rods against the holders or load the system before both rods are seated.

  5. [ 05 / 06 ]

    Slide on the protective frame pads

    Slide one protective frame pad over the free end of each fitted rod and towards the wall. Do not push the pads onto the rods from the side.

    The animation positions the pad centres approximately 20 cm from the wall. Check the contact positions against your actual bike before loading.

    Both pads must support the frame evenly, clear of cables and components. Keep hold of the bike while checking the contact points.

    [ NOTE ]

    The pads are fitted only after both rods are fully seated.

    [ WARNING ]

    Do not use the mount if the frame cannot sit safely and evenly on both pads.

  6. [ 06 / 06 ]

    Hang the bike

    Lift the bike securely and gently lower the frame onto both soft contact points.

    Make sure the bike is supported evenly and sits horizontally on the mount.

    Keep hold of the bike while checking that it is stable and cannot slide from either contact point.

    [ WARNING ]

    Do not release the bike until you have confirmed that the frame is correctly positioned on both contact points and the bike is stable. Do not use the mount for bikes exceeding 15 kg.

Final check.

Complete every check before using the product.

Using your product.

To store your bike, lift it securely and gently lower the frame onto both soft contact points.

Make sure the bike is fully supported and balanced before releasing it.

To remove the bike, support it securely with both hands and lift the frame completely clear of both contact points before moving the bike away from the wall.

Always place and remove the bike in a controlled movement. Do not pull, twist or slide the bike sideways across the contact points.

Care and adjustments.

Wipe the mount and soft contact points clean with a soft, damp cloth. Do not use aggressive solvents or abrasive cleaning products.

Periodically check the mount, contact points and wall fixings for movement, damage or wear. Retighten the mounting screws if required.

Inspect the mount before use and stop using the product if any part is damaged, cracked or no longer securely attached to the wall.

Questions about this product.

Which wall types is this mount suitable for?

The Wall Mount for Road and Gravel Bikes is designed for suitable solid walls, including solid masonry, concrete, brick and solid wood.

Do not install the mount on hollow walls or plasterboard partitions.

Is the mounting hardware included?

Yes. The pair includes two stainless-steel 5 × 40 mm screws, two M5 washers, two 8 × 40 mm wall plugs and two screw caps.

Use the supplied plugs only in suitable solid walls. They are not intended for hollow walls.

Which bikes does it fit?

The mount is designed for road and gravel bikes whose frame can rest securely on both soft contact points.

Before installation, check that the frame can be supported evenly without the contact points interfering with cables, components or other unsuitable areas of the bike.

The maximum permitted bike weight is 15 kg.

Need help?

Send a photo of your setup and tell us where you get stuck.

Contact StudioVelo3D